Configuration

Faucet configuration

Faucet is configured with a YAML-based configuration file, faucet.yaml. The following is example demonstrating a few common features:

faucet.yaml
include:
    - acls.yaml

vlans:
    office:
        vid: 100
        description: "office network"
        acls_in: [office-vlan-protect]
        faucet_mac: "0e:00:00:00:10:01"
        faucet_vips: ['10.0.100.254/24', '2001:100::1/64', 'fe80::c00:00ff:fe00:1001/64']
        routes:
            - route:
                ip_dst: '192.168.0.0/24'
                ip_gw: '10.0.100.2'
    guest:
        vid: 200
        description: "guest network"
        faucet_mac: "0e:00:00:00:20:01"
        faucet_vips: ['10.0.200.254/24', '2001:200::1/64', 'fe80::c00:00ff:fe00:2001/64']

routers:
    router-office-guest:
        vlans: [office, guest]

dps:
    sw1:
        dp_id: 0x1
        hardware: "Open vSwitch"
        interfaces:
            1:
                name: "h1"
                description: "host1 container"
                native_vlan: office
                acls_in: [access-port-protect]
            2:
                name: "h2"
                description: "host2 container"
                native_vlan: office
                acls_in: [access-port-protect]
            3:
                name: "g1"
                description: "guest1 container"
                native_vlan: guest
                acls_in: [access-port-protect]
            4:
                name: "s1"
                description: "services container"
                native_vlan: office
                acls_in: [service-port-protect]
            5:
                name: "trunk"
                description: "VLAN trunk to sw2"
                tagged_vlans: [office]
                acls_in: [access-port-protect]
    sw2:
        dp_id: 0x2
        hardware: "Allied-Telesis"
        interfaces:
            1:
                name: "pi"
                description: "raspberry pi"
                native_vlan: office
                acls_in: [access-port-protect]
            2:
                name: "laptop"
                description: "guest laptop"
                native_vlan: guest
                acls_in: [access-port-protect]
            4:
                name: "s1"
                description: "services Laptop"
                native_vlan: guest
                acls_in: [access-port-protect]
            24:
                name: "trunk"
                description: "VLAN trunk to sw1"
                tagged_vlans: [office, guest]
acls.yaml
acls:
    office-vlan-protect:
        # Prevent IPv4 communication betwen Office/Guest networks
        - rule:
            dl_type: 0x800      # ipv4
            ipv4_src: 10.0.100.0/24
            ipv4_dst: 10.0.200.0/24
            actions:
                allow: 0        # drop
        - rule:
            actions:
                allow: 1        # allow

    access-port-protect:
        # Drop dhcp servers
        - rule:
            dl_type: 0x800      # ipv4
            nw_proto: 17        # udp
            udp_src: 67         # bootps
            udp_dst: 68         # bootpc
            actions:
                allow: 0        # drop
        # Drop dhcpv6 servers
        - rule:
            dl_type: 0x86dd     # ipv6
            nw_proto: 17        # udp
            udp_src: 547        # dhcpv6-server
            udp_dst: 546        # dhcpv6-client
            actions:
                allow: 0        # drop
        # Drop icmpv6 RAs
        - rule:
            dl_type: 0x86dd     # ipv6
            nw_proto: 58        # icmpv6
            icmpv6_type: 134    # router advertisement
            actions:
                allow: 0        # drop
        # Drop SMTP
        - rule:
            dl_type: 0x800      # ipv4
            nw_proto: 6         # tcp
            tcp_dst: 25         # smtp
            actions:
                allow: 0        # drop
        # Force DNS to our DNS server
        - rule:
            dl_type: 0x800      # ipv4
            nw_proto: 17        # udp
            udp_dst: 53         # dns
            actions:
                output:
                    set_fields:
                        - eth_dst: "72:b8:3c:4c:dc:4d"
                    port: "s1"  # s1 container
        # Force DNS to our DNS server
        - rule:
            dl_type: 0x800      # ipv4
            nw_proto: 6         # tcp
            tcp_dst: 53         # dns
            actions:
                output:
                    set_fields:
                        - eth_dst: "72:b8:3c:4c:dc:4d"
                    port: "s1"  # s1 container
        - rule:
            actions:
                allow: 1        # allow

    service-port-protect:
        # Drop icmpv6 RAs
        - rule:
            dl_type: 0x86dd     # ipv6
            nw_proto: 58        # icmpv6
            icmpv6_type: 134    # router advertisement
            actions:
                allow: 0        # drop
        # Drop SMTP
        - rule:
            dl_type: 0x800      # ipv4
            nw_proto: 6         # tcp
            tcp_dst: 25         # smtp
            actions:
                allow: 0        # drop
        - rule:
            actions:
                allow: 1        # allow

The datapath ID may be specified as an integer or hex string (beginning with 0x).

A port not explicitly defined in the YAML configuration file will be left down and will drop all packets.

Configuration options

Top Level

Faucet.yaml
Attribute Type Default Description
acls dictionary {} Configuration specific to acls. The keys are names of each acl, and the values are config dictionaries holding the acl’s configuration (see below).
dps dictionary {} Configuration specific to datapaths. The keys are names or dp_ids of each datapath, and the values are config dictionaries holding the datapath’s configuration (see below).
meters dictionary {} Configuration specific to meters. The keys are names of each meter, and the values are config dictionaries holding the meter’s configuration (see below).
routers dictionary {} Configuration specific to routers. The keys are names of each router, and the values are config dictionaries holding the router’s configuration (see below).
version integer 2 The config version. 2 is the only supported version.
vlans dictionary {} Configuration specific to vlans. The keys are names or vids of each vlan, and the values are config dictionaries holding the vlan’s configuration (see below).

DP

DP configuration is entered in the ‘dps’ configuration block. The ‘dps’ configuration contains a dictionary of configuration blocks each containing the configuration for one datapath. The keys can either be string names given to the datapath, or the OFP datapath id.

dps: <dp name or id>: {}
Attribute Type Default Description
advertise_interval integer 30 How often to advertise (eg. IPv6 RAs)
arp_neighbor_timeout integer 250 ARP and neighbour timeout in seconds
description string name Description of this datapath, strictly informational
dot1x dictionary {} 802.1X configuration (see below)
dp_id integer The configuration key The OFP datapath-id of this datapath
drop_bpdu boolean True If True, Faucet will drop all STP BPDUs arriving at the datapath. NB: Faucet does not handle BPDUs itself, if you disable this then you either need to configure an ACL to catch BDPUs or Faucet will forward them as though they were normal traffic.
drop_broadcast_source_address boolean True If True, Faucet will drop any packet from a broadcast source address
drop_lldp boolean True If True, Faucet will drop all LLDP packets arriving at the datapath.
drop_spoofed_faucet_mac boolean True If True, Faucet will drop any packet it receives with an ethernet source address equal to a MAC address that Faucet is using.
group_table boolean False If True, Faucet will use the OpenFlow Group tables to flood packets. This is an experimental feature that is not fully supported by all devices and may not interoperate with all features of faucet.
hardware string “Open vSwitch” The hardware model of the datapath. Defaults to “Open vSwitch”. Other options can be seen in the documentation for valve.py
high_priority integer low_priority + 1 (9001) The high priority value.
highest_priority integer high_priority + 98 (9099) The highest priority number to use.
ignore_learn_ins integer 10 Ignore every approx nth packet for learning. 2 will ignore 1 out of 2 packets; 3 will ignore 1 out of 3 packets. This limits control plane activity when learning new hosts rapidly. Flooding will still be done by the dataplane even with a packet is ignored for learning purposes.
interfaces dictionary {} Configuration block for interface specific config (see below)
interface_ranges dictionary {} Contains the config blocks for sets of multiple interfaces. The configuration entered here will be used as the defaults for these interfaces. The defaults can be overwritten by configuring the interfaces individually, which will also inherit all defaults not specifically configured. For example, if the range specifies tagged_vlans: [1, 2, 3], and the individual interface specifies tagged_vlans: [4], the result will be tagged_vlans: [4]. The format for the configuration key is a comma separated string. The elements can either be the name or number of an interface or a range of port numbers eg: “1-6,8,port9”.
learn_ban_timeout integer 10 When a host is rapidly moving between ports Faucet will stop learning mac addresses on one of the ports for this number of seconds.
learn_jitter integer 10 In order to reduce load on the controller Faucet will randomly vary the timeout for learnt mac addresses by up to this number of seconds.
lldp_beacon dictionary {} Configuration block for LLDP beacons
low_priority integer low_priority + 9000 (9000) The low priority value.
lowest_priority integer priority_offset (0) The lowest priority number to use.
max_host_fib_retry_count integer 10 Limit the number of times Faucet will attempt to resolve a next-hop’s l2 address.
max_hosts_per_resolve_cycle integer 5 Limit the number of hosts resolved per cycle.
max_resolve_backoff_time integer 32 When resolving next hop l2 addresses, Faucet will back off exponentially until it reaches this value.
metrics_rate_limit_sec integer 0 Rate limit metric updates - don’t update metrics if last update was less than this many seconds ago.
name string The configuration key A name to reference the datapath by.
ofchannel_log string None Name of logfile for openflow logs
packetin_pps integer None Ask switch to rate limit packet pps.
priority_offset integer 0 Shift all priority values by this number.
proactive_learn_v4 boolean True Whether proactive learning is enabled for IPv4 nexthops
proactive_learn_v6 boolean True Whether proactive learning is enabled for IPv6 nexthops
stack dictionary {} Configuration block for stacking config, for loop protection (see below)
timeout integer 300 Timeout for MAC address learning
use_idle_timeout boolean False Turn on/off the use of idle timeout for src_table, default OFF.
table_sizes dictionary {} For TFM based switches, size of each FAUCET table (all must be specified)
global_vlan int 2**11-1 When global routing is enabled, FIB VID used internally

Stacking (DP)

Stacking is configured in the dp configuration block and in the interface configuration block. At the dp level the following attributes can be configured withing the configuration block ‘stack’:

dps: <dp name or id>: stack: {}
Attribute Type Default Description
priority integer 0 Setting any value for stack priority indicates that this datapath should be the root for the stacking topology.

LLDP (DP)

LLDP beacons are configured in the dp and interface configuration blocks.

LLDP beacons can be used to, among other things, facilitate physical troubleshooting (e.g. so that a standard cable tester can display port information), verify FAUCET stacking topology, and cue a phone to use the right voice VLAN.

NOTE: while FAUCET can receive and log LLDP from other devices, FAUCET does not do spanning tree those LLDP packets will have no influence on FAUCET’s forwarding decisions.

The following attributes can be configured withing the ‘lldp_beacon’ configuration block at the dp level:

dps: <dp name or id>: lldp_beacon: {}
Attribute Type Default Description
system_name string The datapath name System name inside LLDP packet
send_interval integer None Seconds between sending beacons
max_per_interval integer None The maximum number of beacons, across all ports to send each interval

802.1X (DP)

Note

802.1X support is experimental, and there may be incomplete features or bugs. If you find an issue please email the mailing list or create an Github issue.

Faucet implements 802.1X by forwarding EAPOL packets on the dataplane to a socket it is listening on. These packets are then passed through to a RADIUS server which performs the authentication and generates the reply message.

For each instance of Faucet there is only one 802.1X speaker. This 802.1X speaker is configured by the options below. Except for the ‘nfv_sw_port’ option, the configuration for the speaker is configured using the first dp’s dot1x config dictionary. For all other dps only the ‘nfv_sw_port’ option is required with the others ignored.

A basic network and configuration with two hosts may look like:

ACL network diagram

A brief overview of the current state of the implementation:

Implemented:

  • EAP Types: MD5, PEAP, TLS, TTLS.
  • Authentication session expiry default 3600 seconds. (configurable (per authentication) via returning the Session-Timeout attribute in the RADIUS Access-Accept message).
  • Faucet connects to a single RADIUS server, and passes through all EAP messages.
  • Client can end session with EAP-Logoff.

Not Supported (yet):

  • RADIUS Accounting.
  • Multiple RADIUS Servers.
  • Other EAP types. E.g. FAST, …
  • Dynamic assignment of VLAN/ACL.

802.1X port authentication is configured in the dp configuration block and in the interface configuration block. At the dp level the following attributes can be configured with the configuration block ‘dot1x’:

dps: <dp name or id>: dot1x: {}
Attribute Type Default Description
nfv_intf str   The interface for Faucet to listen for EAP packets from the dataplane. - NOTE: Faucet will only use the config from the first dp
nfv_sw_port int   Switch port number that connects to the Faucet server’s nfv_intf
radius_ip str   IP address of RADIUS Server the 802.1X speaker will authenticate with. - NOTE: Faucet will only use the config from the first dp
radius_port int 1812 UDP port of RADIUS Server the 802.1X speaker will authenticate with. - NOTE: Faucet will only use the config from the first dp
radius_secret str   Shared secret used by the RADIUS server and the 802.1X speaker. - NOTE: Faucet will only use the config from the first dp

Interfaces

Configuration for each interface is entered in the ‘interfaces’ configuration block withing the config for the datapath. Each interface configuration block is a dictionary keyed by the interface name.

Defaults for groups of interfaces can also be configured under the ‘interface-ranges’ attribute within the datapath configuration block. These provide default values for a number of interfaces which can be overwritten with the config block for an individual interface. These are keyed with a string containing a comma separated list of OFP port numbers, interface names or with OFP port number ranges (eg. 1-6).

dps: <dp name or id>: interfaces: <interface name or OFP port number>: {}
Attribute Type Default Description
acl_in integer or string None Deprecated, replaced by acls_in which accepts a list. The acl that should be applied to all packets arriving on this port. referenced by name or list index
acls_in a list of ACLs, as integers or strings None A list of ACLs that should be applied to all packets arriving on this port. referenced by name or list index. ACLs listed first take priority over those later in the list.
description string Name (which defaults to the configuration key) Description, purely informational
dot1x boolean False Enable 802.1X port authentication
enabled boolean True Allow packets to be forwarded through this port.
hairpin boolean False If True it allows packets arriving on this port to be output to this port. This is necessary to allow routing between two vlans on this port, or for use with a WIFI radio port.
lldp_beacon dictionary {} Configuration block for lldp configuration
loop_protect boolean False if True, do simple (host/access port) loop protection on this port.
loop_protect_external boolean False if True, do external (other switch) loop protection on this port.
max_hosts integer 255 the maximum number of mac addresses that can be learnt on this port.
mirror a list of integers or strings None Mirror all allowed packets recieved from (subject to ACLs), and all packets transmitted to, the ports specified (by name or by port number), to this port. If mirroring of denied by ACL packets is desired, use the ACL rule mirror option.
name string The configuration key. a name to reference this port by.
native_vlan integer None The vlan associated with untagged packets arriving and leaving this interface.
number integer The configuration key. The OFP port number for this port.
opstatus_reconf boolean True If True, FAUCET will reconfigure the pipeline based on operational status of the port.
output_only boolean False If True, no packets will be accepted from this port.
override_output_port integer None If set, packets are sent to this other port.
permanent_learn boolean False When True Faucet will only learn the first MAC address on this interface. All packets with an ethernet src address not equal to that MAC address will be dropped.
stack dictionary None configuration block for interface level stacking configuration
tagged_vlans list of integers or strings None The vlans associated with tagged packets arriving and leaving this interfaces.
unicast_flood boolean True If False unicast packets will not be flooded to this port.

Stacking (Interfaces)

Stacking port configuration indicates how datapaths are connected when using stacking. The configuration is found under the ‘stack’ attribute of an interface configuration block. The following attributes can be configured:

dps: <dp name or id>: interfaces: <interface name or port number: stack: {}
Attribute Type Default Description
dp integer or string None The name of dp_id of the dp connected to this port
port integer or string None The name or OFP port number of the interface on the remote dp connected to this interface.

LLDP (Interfaces)

Interface specific configuration for LLDP.

dps: <dp name or id>: interfaces: <interface name or port number: lldp_beacon: {}
Attribute Type Default Description
enable boolean False Enable sending lldp beacons from this interface
org_tlvs list [] Definitions of Organisational TLVs to add to LLDP beacons
port_descr string Interface description Port description to use in beacons from this interface
system_name string lldp_beacon (dp) system name The System Name to use in beacons from this interface

LLDP Organisational TLVs (Interfaces)

Faucet allows defining organisational TLVs for LLDP beacons. These are configured in a list under lldp_beacons/org_tlvs at the interfaces level of configuration.

Each list element contains a dictionary with the following elements:

dps: <dp name or id>: interfaces: <interface name or port number: lldp_beacon: org_tlvs: - {}
Attribute Type Default Description
info string None The info field of the tlv, as a hex string
oui integer None The Organisationally Unique Identifier
subtype integer None The organizationally defined subtype

Router

Routers config is used to allow routing between VLANs, and optionally BGP. Routers configuration is entered in the ‘routers’ configuration block at the top level of the faucet configuration file. Configuration for each router is an entry in the routers dictionary and is keyed by a name for the router. The following attributes can be configured:

routers: <router name>: {}
Attribute Type Default Description
vlans list of integers or strings None Enables inter-vlan routing on the given VLANs.
bgp BGP configuration. None See below for BGP configuration.

BGP

Routers config to enable BGP routing.

routers: <router name>: {}
Attribute Type Default Description
as integer None The local AS number to used when speaking BGP
connect_mode string “passive” Must be “passive”
neighbor_addresses list of strings (IP addresses) None The list of BGP neighbours
neighbor_as integer None The AS Number for the BGP neighbours
routerid string (IP address) None BGP router ID.
server_addresses list of strings (IP addresses) None IP addresses for FAUCET to listen for incoming BGP addresses.
port integer None Port to use for BGP sessions
vlan string None The VLAN to add/remove BGP routes from.

VLAN

VLANs are configured in the ‘vlans’ configuration block at the top level of the faucet config file. The config for each vlan is an entry keyed by its vid or a name. The following attributes can be configured:

vlans: <vlan name or vid>: {}
Attribute Type Default Description
acl_in string or integer None Deprecated, replaced by acls_in which accepts a list. The acl to be applied to all packets arriving on this vlan.
acls_in a list of ACLs, as integers or strings None The acl to be applied to all packets arriving on this vlan. ACLs listed first take priority over those later in the list.
description string None Strictly informational
faucet_vips list of strings (IP address prefixes) None The IP Address for Faucet’s routing interface on this vlan
faucet_mac string (MAC address) None Set MAC for FAUCET VIPs on this VLAN
max_hosts integer 255 The maximum number of hosts that can be learnt on this vlan.
minimum_ip_size_check boolean True If False, don’t check that IP packets have a payload (must be False for OVS trace/tutorial to work)
name string the configuration key A name that can be used to refer to this vlan.
proactive_arp_limit integer 2052 Do not proactively ARP for hosts once this value has been reached (set to None for unlimited)
proactive_nd_limit integer 2052 Don’t proactively discover IPv6 hosts once this value has been reached (set to None for unlimited)
routes list of routes None Static routes configured on this vlan (see below)
targeted_gw_resolution boolean False If True, and a gateway has been resolved, target the first re-resolution attempt to the same port rather than flooding.
unicast_flood boolean True If False packets to unknown ethernet destination MAC addresses will be dropped rather than flooded.
vid integer the configuration key The vid for the vlan.

Static Routes

Static routes are given as a list. Each entry in the list contains a dictionary keyed with the keyword ‘route’ and contains a dictionary configuration block as follows:

vlans: <vlan name or vid>: routes: - route: {}
Attribute Type Default Description
ip_dst string (IP subnet) None The destination subnet.
ip_gw string (IP address) None The next hop for this route

Meters

Note

Meters are platform dependent and not all functions may be available.

Meters are configured under the ‘meters’ configuration block. The meters block contains a dictionary of individual meters each keyed by its name.

meters: <meter name>:
Attribute Type Default Description
meter_id int   Unique identifier.
entry dictionary   Defines the meter actions. Details Below.
: meters: <meter name>: entry:
Attribute Type Default Desciption
flags string or list of strings KBPS Possible values are ‘KBPS’ (Rate value in kb/s (kilo-bit per second).), ‘PKTPS’ (Rate value in packet/sec.), ‘BURST’ (Do burst size), ‘STATS’ (Collect statistics)
bands list of bands (which are dictionaries, see below)    
: meters: <meter name>: entry: bands:
Attribute Type Default Desciption
type string   ‘DROP’ - drop apckets when the band rate is exceeded, or ‘DSCP_REMARK’- use a simple DiffServ policer to remark the DSCP field in the IP header of packets that exceed the band rate.
rate int   Rate for dropping or remarking packets, depending on the above type. Value is in KBPS or PKTPS flag depending on the flag set.
burst_size int   Only used if flags includes BURST. Indicates the length of packet or byte burst to consider for applying the meter.
prec_level int   Only used if type is DSCP_REMARK. The amount by which the drop precedence should be increased.

ACLs

ACLs are configured under the ‘acls’ configuration block. The acls block contains a dictionary of individual acls each keyed by its name.

Each acl contains a list of rules: a packet will have the first matching rule applied to it.

Each rule is a dictionary containing the single key ‘rule’ with matches and actions. Matches are key/values based on the ryu RESTFul API. Actions is a dictionary of actions to apply upon match.

: acls: <acl name>: - rule: actions: {}
Attribute Type Default Description
allow boolean False If True allow the packet to continue through the Faucet pipeline, if False drop the packet.
force_port_vlan boolean False if True, don’t verify VLAN/port association.
cookie int, 0-2**16 defaults to datapath cookie value If set, cookie on this flow will be set to this value.
meter string None Meter to apply to the packet
mirror string or integer None Copy the packet, before any modifications, to the specified port (NOTE: ACL mirroring is done in input direction only)
output dictionary None Used to output a packet directly. Details below.

The output action contains a dictionary with the following elements:

: acls: <acl name>: - rule: actions: output: {}
Attribute Type Default Description
set_fields list of dictionaries None A list of fields to set with values, eg. eth_dst: “1:2:3:4:5:6”
port integer or string None The port to output the packet to.
ports list of [ integer or string ] None The list of ports the packet will be output through.
pop_vlans boolean False Pop vlan tag before output.
vlan_vid integer False Push vlan tag before output.
swap_vid integer None Rewrite the vlan vid of the packet when outputting
vlan_vids list of [ integer or {vid: integer, eth_type: integer} ] None Push vlan tags on output, with optional eth_type.
failover dictionary None Output with a failover port (see below).

Failover is an experimental option, but can be configured as follows:

: acls: <acl name>: - rule: actions: output: failover: {}
Attribute Type Default Description
group_id integer None The OFP group id to use for the failover group
ports list None The list of ports the packet can be output through.

Gauge configuration

Gauge is configured similarly with, gauge.yaml. The following is an example demonstrating a few common features:

gauge.yaml
# Recommended configuration is Prometheus for all monitoring, with all_dps: True
faucet_configs:
    - '/etc/faucet/faucet.yaml'
watchers:
    port_status_poller:
        type: 'port_state'
        all_dps: True
        #dps: ['sw1', 'sw2']
        db: 'prometheus'
    port_stats_poller:
        type: 'port_stats'
        all_dps: True
        #dps: ['sw1', 'sw2']
        interval: 10
        db: 'prometheus'
        #db: 'influx'
    flow_table_poller:
        type: 'flow_table'
        all_dps: True
        interval: 60
        db: 'prometheus'
dbs:
    prometheus:
        type: 'prometheus'
        prometheus_addr: '0.0.0.0'
        prometheus_port: 9303
    ft_file:
        type: 'text'
        compress: True
        file: 'flow_table.yaml.gz'
    influx:
        type: 'influx'
        influx_db: 'faucet'
        influx_host: 'influxdb'
        influx_port: 8086
        influx_user: 'faucet'
        influx_pwd: 'faucet'
        influx_timeout: 10

Verifying configuration

You can verify that your configuration is correct with the check_faucet_config script:

check_faucet_config /etc/faucet/faucet.yaml

Configuration examples

For complete working examples of configuration features, see the unit tests, tests/faucet_mininet_test.py. For example, FaucetUntaggedACLTest shows how to configure an ACL to block a TCP port, FaucetTaggedIPv4RouteTest shows how to configure static IPv4 routing.

Applying configuration updates

You can update FAUCET’s configuration by sending it a HUP signal. This will cause it to apply the minimum number of flow changes to the switch(es), to implement the change.

pkill -HUP -f faucet.faucet

Configuration in separate files

Extra DP, VLAN or ACL data can also be separated into different files and included into the main configuration file, as shown below. The include field is used for configuration files which are required to be loaded, and Faucet will log an error if there was a problem while loading a file. Files listed on include-optional will simply be skipped and a warning will be logged instead.

Files are parsed in order, and both absolute and relative (to the configuration file) paths are allowed. DPs, VLANs or ACLs defined in subsequent files overwrite previously defined ones with the same name.

faucet.yaml

include:
    - /etc/faucet/dps.yaml
    - /etc/faucet/vlans.yaml

include-optional:
    - acls.yaml

dps.yaml

# Recursive include is allowed, if needed.
# Again, relative paths are relative to this configuration file.
include-optional:
    - override.yaml

dps:
    test-switch-1:
        ...
    test-switch-2:
        ...

Environment variables

You can use environment variables to override default behaviour of faucet such as paths for configuration files and port numbers.

Environment Variable Type Default Description
FAUCET_CONFIG Colon-separated list of file paths
/etc/faucet/faucet.yaml:
/etc/ryu/faucet/faucet.yaml
Faucet will load it’s configuration from the first valid file in list
FAUCET_CONFIG_STAT_RELOAD boolean False If true, faucet will automatically reload itself and apply new configuration when FAUCET_CONFIG changes
FAUCET_LOG_LEVEL Python log level INFO Log verbosity
FAUCET_LOG File path or STDOUT or STDERR
/var/log/faucet/
faucet.log
Location for faucet to log messages to, can be special values STDOUT or STDERR
FAUCET_EXCEPTION_LOG File path or STDOUT or STDERR
/var/log/faucet/
faucet_exception.log
Location for faucet log to log exceptions to, can be special values STDOUT or STDERR
FAUCET_EVENT_SOCK Socket path   Location to a UNIX socket where faucet will write events to, or empty to disable events
FAUCET_PROMETHEUS_PORT Port 9302 TCP port to listen on for faucet prometheus client
FAUCET_PROMETHEUS_ADDR IP address 0.0.0.0 IP address to listen on for faucet prometheus client
GAUGE_CONFIG Colon-separated list of file paths
/etc/faucet/gauge.yaml:
/etc/ryu/faucet/gauge.yaml
Guage will load it’s configuration from the first valid file in list
GAUGE_CONFIG_STAT_RELOAD boolean False If true, gauge will automatically reload itself and apply new configuration when GAUGE_CONFIG changes
GAUGE_LOG_LEVEL Python log level INFO Log verbosity
GAUGE_LOG File path or STDOUT or STDERR
/var/log/faucet/
gauge.log
Location for gauge to log messages to, can be special values STDOUT or STDERR
GAUGE_EXCEPTION_LOG File path or STDOUT or STDERR
/var/log/faucet/
gauge_exception.log
Location for faucet log to log exceptions to, can be special values STDOUT or STDERR
GAUGE_PROMETHEUS_ADDR IP address 0.0.0.0 IP address to listen on for gauge prometheus client