Testing

Installing docker

First, get yourself setup with docker based on our Installing docker documentation.

Software switch testing with docker

First prime the pip cache with the following command (re-run this when upgrading FAUCET also).

sudo ./docker/pip_deps.sh

Then you can build and run the mininet tests from the docker entry-point:

sudo docker build --pull -t faucet/tests -f Dockerfile.tests .
sudo apparmor_parser -R /etc/apparmor.d/usr.sbin.tcpdump
sudo modprobe openvswitch
sudo docker run --sysctl net.ipv6.conf.all.disable_ipv6=0 --privileged -v $HOME/.cache/pip:/var/tmp/pip-cache -ti faucet/tests

The apparmor command is currently required on Ubuntu hosts to allow the use of tcpdump inside the container.

If you need to use a proxy, the following to your docker run command.

--build-arg http_proxy=http://your.proxy:port

Hardware switch testing with docker

                     +--------------------------+
                     |                          |
                     |         FAUCET CPN       |
                     |                          |
                     |                          |
+------------------------------+     +-------------------------+
|                    |         |     |          |              |
|                    |    +--+ |     | +--+     |              |
|                    |    |  +---------+  |     |              |
|   FAUCET test host |    +--+ |     | +--+     |              |
|                    +--------------------------+              |
|                              |     |                         |
|                              |     |                         |
|                              |     |                         |
|                              |     |                         |
|          +---------------------+   |                         |
|          |   +------+   +--+ | |   | +--+                    |
|          |   |VM 1  |   |  +---------+  |                    |
|          |   +------+   +--+ | |   | +--+                    |
|          |                   | |   |                         |
|          |   +------+   +--+ | |   | +--+  OpenFlow switch   |
|          |   |VM 2  |   |  +---------+  |  under test        |
|          |   +------+   +--+ | |   | +--+                    |
|          |                   | |   |                         |
|          |   +------+   +--+ | |   | +--+                    |
|          |   |VM 3  |   |  +---------+  |                    |
|          |   +------+   +--+ | |   | +--+                    |
|          |                   | |   |                         |
|          |   +------+   +--+ | |   | +--+                    |
|          |   |VM 4  |   |  +---------+  |                    |
|          |   +------+   +--+ | |   | +--+                    |
|          |                   | |   |                         |
|          |                   | |   |                         |
+------------------------------+ |   +-------------------------+
           |                     |
           |    MININET          |
           |                     |
           |                     |
           +---------------------+

Requirements

Your test host, requires at least 5 interfaces. 4 interfaces to connect to the dataplane, and one for the CPN for OpenFlow. You will need to assign an IP address to the CPN interface on the host, and configure the switch with a CPN IP address and establish that they can reach each other (eg via ping).

NOTE: it is very important to disable any process that cause any traffic on the dataplane test interfaces, as this may interfere with the tests. For example, the test interfaces should have all IPv4/IPv6 dynamic address assignment disabled. To achieve this, on Ubuntu for example, you can set the interfaces to “unmanaged” in Network Manager, and make sure processes like Avahi ignores those interfaces.

You will need to configure the switch with two OpenFlow controllers, both with the host’s CPN IP address, but with different ports (defaults are given below for of_port and gauge_of_port).

It is assumed that you execute all following commands from your FAUCET source code directory (eg one you have git cloned).

Test configuration

Create a directory for the test configuration:

mkdir -p /etc/faucet
$EDITOR /etc/faucet/hw_switch_config.yaml

hw_switch_config.yaml should contain the correct configuration for your switch:

hw_switch: True
hardware: 'Open vSwitch'
# Map ports on the hardware switch, to physical ports on this machine.
# If using a switch with less than 4 dataplane ports available, run
# FaucetZodiac tests only. A 4th port must still be defined here and
# must exist, but will not be used.
dp_ports:
  1: enp1s0f0
  2: enp1s0f1
  3: enp1s0f2
  4: enp1s0f3
# Hardware switch's DPID
dpid: 0xeccd6d9936ed
# Port on this machine that connects to hardware switch's CPN port.
# Hardware switch must use IP address of this port as controller IP.
cpn_intf: enp5s0
# There must be two controllers configured on the hardware switch,
# with same IP (see cpn_intf), but different ports - one for FAUCET,
# one for Gauge.
of_port: 6636
gauge_of_port: 6637
# If you wish to test OF over TLS to the hardware switch,
# set the following parameters per Ryu documentation.
# https://github.com/osrg/ryu/blob/master/doc/source/tls.rst
# ctl_privkey: ctl-privkey.pem
# ctl_cert: ctl-cert.pem
# ca_certs: /usr/local/var/lib/openvswitch/pki/switchca/cacert.pem

Running the tests

docker build --pull -t faucet/tests -f Dockerfile.tests .
apparmor_parser -R /etc/apparmor.d/usr.sbin.tcpdump
modprobe openvswitch
sudo docker run --privileged --net=host \
    -v $HOME/.cache/pip:/var/tmp/pip-cache \
    -v /etc/faucet:/etc/faucet \
    -v /var/tmp:/var/tmp \
    -ti faucet/tests

Test suite options

In both the software and hardware version of the test suite we can provide flags inside the FAUCET_TESTS environment variable to run specific parts of the test suite.

Note

Multiple flags can be added to FAUCET_TESTS, below are just some examples of how individual flags work.

Running specific integration tests

If specific test names are listed in the FAUCET_TESTS environment then only these integration tests will be run and all others skipped.

If we add the following to either of the previous docker run commands then only the FaucetUntaggedTest will be run.

-e FAUCET_TESTS="FaucetUntaggedTest"

Running only the integration tests

Sometimes you will want to skip the pytype, linting and documentation tests in order to complete a faucet test suite run against hardware quicker.

-e FAUCET_TESTS="-i"

Skip code checks

Sometimes you will want to skip the pytype, linting and documentation tests.

This can be done with with the -n flag:

-e FAUCET_TESTS="-n"

Skip unit tests

Sometimes you will want to skip the unit tests which are small tests that verify small chunks of the code base return the correct values. If these are skipped the integration tests (which spin up virtual networks and tests faucet controllers under different configurations) will still be run.

This can be done with with the -u flag:

-e FAUCET_TESTS="-u"

Checking test results

If a test fails, you can look in /var/tmp - there will be subdirectories created for each test, which will contain all the logs and debug information (including tcpdumps).

By default the test suite cleans up these files but if we use the -k flag the test suite will keep these files.

-e FAUCET_TESTS="-k"